Ron
07/09/2009
02:48:15 PM
|
Garmin GPS
The spring in the battery slot has broken and the clip plate was also broken. Were or how can I get it fixed. Its pretty expensive for such a small part to cause its downfall.
|
|
|
Clifton G van Putten
07/14/2009
12:18:08 PM
|
new screen and sevice.
I have a garmin 125 gps and a 128 needsa new screen. I would like to know if this can be done and how long will it take.
|
|
|
Ed Downey
07/15/2009
03:46:54 PM
|
Broken Screen on Garmin Nuvi 750
Sir:
I broke the screen on my Garmin Nuvi 750, can it be fixed?
Ed Downey
|
|
|
Warren
07/21/2009
08:52:22 AM
|
screen doesn't respond to what is touched
The system has power but it doesn't respond properly to what is touched. Example: when i touch a certain letter, another untouched letter appears. I use my GPS a great deal, how can I get this resolved ?
|
|
|
Jose
07/22/2009
01:17:17 AM
|
Broken LCD/Window on Nuvi 260w
Is there a way to replace the broken LCD on my Nuvi GPS or do I need to buy a new gps????
|
|
|
ansari
07/22/2009
03:24:16 AM
|
nuvi200
I have Garmin nuvi200.. i download and delete one map from the internet after that i tried to switch on Garmin but it failed and the following message came:\r\n
"No detailed maps found that support routing. The nuvy cannot be used without them"
|
|
|
Rex DeVall
07/28/2009
09:20:10 PM
|
Garmin Street Pilot
MY GPS fell from my windshield and now it will not power up.
Can it be repaired?
rldd@intrstar.net
|
|
|
mitch
08/02/2009
03:20:31 AM
|
garmin gps repair
as long as your garmin gps is not stollen garmin has a flat rate replacement fee and they give you a 90 day warranty on the replacement as well you can call them with the serial number to see if it is registered to anyone if you purchased your garmin used their phone is 800 800 1020
|
|
|
Walkerjoeb
08/08/2009
02:58:22 PM
|
GARMIN GPS 75 HH Repair Service
GARMIN has discontinued any repair / Upgrade for HH Garmin GPS 75 due to age of unit. My unit turns on and displays all pages and stored WPs but does not receive satilite info ,positions or receive levels. Does anyone know where I can have unit software upgraded /repaired ?
Joe
|
|
|
11/12/2009
02:18:39 PM
|
|
|
|
wil o'connell
11/24/2009
01:03:45 PM
|
broken garmin nuvi
my garmin was hit on the window,now i cannot view anything on the screen. the glass itself is not broken. is there any repair for the lcd inside. it is brand new,im hoping there is something that can be done. thank you.
|
|
|
wil o'connell
11/24/2009
01:07:17 PM
|
e-mail
the garmin is a Nuvi 255W e-mail is bgoc1263@aol.com thanks
|
|
|
Samy
11/27/2009
11:31:20 PM
|
Garmin cannot be repaired
If I cannot repair my Garmin is there any way I can exchange for new model? I guess it can be used for parts...
|
|
|
Janet Whiteway
11/29/2009
10:21:10 PM
|
Garmin 260
I have a 260 Garmin got it last April and when you plug it in to be charged it won't work until it is unpluged again can you help me what is wrong
|
|
|
Janet
11/29/2009
10:27:28 PM
|
Garmin 260
I have a 260 garmin that when you plug it in to be charged it won't work can anyone know what is wrong with it e-mail jswhiteway@ruranet.com
|
|
|
michael
12/02/2009
09:25:21 PM
|
broken screen
i have a garmin Nuvi 200 and the screen broke i was wondering if it could be fixed
|
|
|
kathleen fitzgerald
12/03/2009
02:37:52 PM
|
garmin nuvi 650
Reply to Warren's post dated 7/21/2009 8:52:22 AM
garmin gps doen not respond to the letter that is touched. What can be done about this??
|
|
|
jose
12/16/2009
01:15:03 AM
|
tapa de las baterias
tengo un gps garmin se me perdio la tapa donde van las pilas. donde puedo conseguir unä?
|
|
|
Fernando Zambrana
12/29/2009
01:07:24 AM
|
Garmin nuvi 350
My Garmin Nuvi 350 is the best that Garmin has made. I have tried other nuvi but none of them give the feature of street names sound on each intersection and left and right turns. After 3 years, it broke. Because this one nolonger is made, I have tried others presently avaible nuvis with no match to my old Nuvi 350. Where can I have my Nuvi 350 repaired or exchange? fernandozambrana28@yahoo.com
|
|
|
cessna823
01/09/2010
10:46:55 AM
|
What Model GPS Garmin you working on
|
|
|
cessna823
01/09/2010
11:07:48 AM
|
Reply to Jose's post dated 7/22/2009 1:17:17 AM
remove garmin name lable, remove 2 screws t-2 or t3 torx could move out with phillips head more work, take screw driver straight edge start on end that doesnt have on/off swtich and pry up and towards your face once open put a 2nd screw driver or fork or what ever to hold open and work on the other same side other end , keep in mind the frame has MAle slot edge anchors that sit into female slot and you are lifting male out of female and then apart, once you have the no on/off switch end open work on one side back to the on/off switch end but save that for last, open the other end and last open the on/off switch end just watch the on/off button is held in place by Garmin frame and on/off button switch slides in. Dont drop in to Toliet or Garbage disposal, When you resasemble the curve end of the on/off button goes toward the Screen and straight side goes to case,frame center. Once open tear tape off of Circuit board and look at white lock door take screwdriver pry up to your face and POW the Screen Ribbion Cable lift off Circuit Board, Place new Screen onto Garmin and use your belly to hold Garmin while placing new ribbion cable into contact now take screwdriver and close lock door....now take and fire your Garmin up like Normal...If Screen Goes All White or Does nothing ....Release Cable Ribbion Lock door recenter and lock door again ....Make sure battery is good or have power pluged in when testing ....everything checks take put tape over lock door on circuit board and put on/off button in place, reposition the Case and Screen Frame in alignment ....SQUEEZE POW ---All Snap Into Place...Put Old Screws back in dont over tighten just snug....REplace Garmin LABLE ....You have Just Replaced your Screen...NOTE: There are 2 Connectors on the Circuit Board On 2-Wire for the speaker and 3-Wire for the Battery that sits into case with more tape glue holding into place....Maybe good time to Replace battery Both connectors will slide out of circuit board and will both are different so you wont screw up,,,,just look at the side that is up so when you put together you will see Flat side UP ...!!! That is IT have Fun Keep Smiling and NEVER NEVER Touch Circuit Board With Solidering Iron Accept Where Power,Gnd,Data Connector Anchors to The Circuit Board....BE A MAN AND FIX IT....HAVE FUN ...God Bless
|
|
|
cessna823
01/09/2010
11:08:44 AM
|
Reply to Janet Whiteway's post dated 11/29/2009 10:21:10 PM
remove garmin name lable, remove 2 screws t-2 or t3 torx could move out with phillips head more work, take screw driver straight edge start on end that doesnt have on/off swtich and pry up and towards your face once open put a 2nd screw driver or fork or what ever to hold open and work on the other same side other end , keep in mind the frame has MAle slot edge anchors that sit into female slot and you are lifting male out of female and then apart, once you have the no on/off switch end open work on one side back to the on/off switch end but save that for last, open the other end and last open the on/off switch end just watch the on/off button is held in place by Garmin frame and on/off button switch slides in. Dont drop in to Toliet or Garbage disposal, When you resasemble the curve end of the on/off button goes toward the Screen and straight side goes to case,frame center. Once open tear tape off of Circuit board and look at white lock door take screwdriver pry up to your face and POW the Screen Ribbion Cable lift off Circuit Board, Place new Screen onto Garmin and use your belly to hold Garmin while placing new ribbion cable into contact now take screwdriver and close lock door....now take and fire your Garmin up like Normal...If Screen Goes All White or Does nothing ....Release Cable Ribbion Lock door recenter and lock door again ....Make sure battery is good or have power pluged in when testing ....everything checks take put tape over lock door on circuit board and put on/off button in place, reposition the Case and Screen Frame in alignment ....SQUEEZE POW ---All Snap Into Place...Put Old Screws back in dont over tighten just snug....REplace Garmin LABLE ....You have Just Replaced your Screen...NOTE: There are 2 Connectors on the Circuit Board On 2-Wire for the speaker and 3-Wire for the Battery that sits into case with more tape glue holding into place....Maybe good time to Replace battery Both connectors will slide out of circuit board and will both are different so you wont screw up,,,,just look at the side that is up so when you put together you will see Flat side UP ...!!! That is IT have Fun Keep Smiling and NEVER NEVER Touch Circuit Board With Solidering Iron Accept Where Power,Gnd,Data Connector Anchors to The Circuit Board....BE A MAN AND FIX IT....HAVE FUN ...God Bless
|
|
|
SHARCNET
01/14/2010
11:18:47 AM
|
Repair
Nuvi Repair site:
http://www.sharcnet-usa.com
Nuvi Help Site:
http://www.gpsobsession.com
|
|
|
Erna
01/25/2010
06:15:54 AM
|
Broken glass
Reply to Jose's post dated 7/22/2009 1:17:17 AM
Unfortunately, I let my gps slipped onto the floor : broken window and most of the touch-funvtions does not work. Is it reparable? I'm living in Pretoria, South Africa. Please help
|
|
|
Erna
01/25/2010
06:18:05 AM
|
Broken glass
Reply to Jose's post dated 7/22/2009 1:17:17 AM
Unfortunately, I let my gps slipped onto the floor : broken window and most of the touch-funvtions does not work. Is it reparable? I'm living in Pretoria, South Africa. Please help. Forgot to mention, It's a Garmin 215W
|
|
|
snow
01/25/2010
03:44:07 PM
|
garmin where 2
my garmin is locked and i wont too now how i can unlock it
|
|
|
Alf Watts
02/19/2010
09:14:11 AM
|
Broken garmin screen
Reply to Erna's post dated 1/25/2010 6:18:05 AM
What model garmin is it?
|
|
|
Alf Watts
02/19/2010
09:15:14 AM
|
Screen recalibration
Reply to Warren's post dated 7/21/2009 8:52:22 AM
What model garmin is it?
|
|
|
Alf Watts
02/19/2010
09:19:18 AM
|
Broken screen Garmin
Reply to wil o'connell's post dated 11/24/2009 1:03:45 PM
What model Garmin is it?
|
|
|
Fred
02/19/2010
09:29:24 AM
|
Broken screen nuvi 205W
Reply to Alf Watts's post dated 2/19/2010 9:14:11 AM
I am looking for a Garmin Nuvi 205W which has a broken screen for spares.
|
|
|
w.sorocco@sbcglobal.net
02/26/2010
11:07:30 PM
|
Garmin Nuvi 650 GPS w/broken glass
I have a broken glass where can I purchase a new or used lens?
Bill
|
|
|
dspolson
02/28/2010
09:08:27 PM
|
Garmin GPS III+ Repair
I'm looking for someone who can repair my gps, it needs a new memory battery, and it no longer displays satelite data, but it does display the pages. It was a reliable unit for amost 15 years, and i would like to be albe to resurect it. I have other units, but this is my favorite.
|
|
|
Susan
03/05/2010
03:54:14 AM
|
Broken screen 215
Reply to Erna's post dated 1/25/2010 6:18:05 AM
Ema, have you had it repaired yet? If not let us know via this forum. I may be able to help you! I'm in Durban South Africa.
|
|
|
Gwen
03/12/2010
02:38:15 PM
|
Streetpilot c580 - no sound
I think a fuse blew because I plugged it in my friend's car- and they forgot to tell me the cigarette lighter wasn't working properly... (nice friend, huh).. so no my garmin has no sound. Where can I take it to get it repaired? All else works fine.
Thanks!
|
|
|
nick
03/13/2010
05:50:58 PM
|
Broken screen nuvi 205W - Another issue
The suction cup came loose and my unit tumbled. The screen is now faulty in a couple spots. How can I get this repaired? I'd rather send it somewhere unless it's easy to DIY. Where can I get/what kind of parts do I need? Thanks.
|
|
|
onerellen
03/15/2010
11:45:02 PM
|
GPS car tracking system
Our company is a professional car alarm supplier. Our company is an ISO 9001:2000 certified enterprise. We have been granted 3C and CE certificate, and our car alarm is awarded with patent in China. Our products are the best choice for cars, because it is of good performance, strong features and high quality.
Our car alarms are advanced car security product developed by our company. It takes advantage of mobile phone networks to tackle any problems, it can always enable you keep in touch with your car conveniently. You can supervise, protect and control your beloved car anywhere anytime. It provides the most cost-effective protection service for the cars owners
and we can produce the car alarms according to the clients' requirements, for example, if you want to change some of the product's functions, we can do this for you when the order quantity can meet a required order quantity.
We believe good quality is always the point. If you are interested in our products, please feel free to contact us. www.oneralarm.com .
MSN:oneralarm02@gmail.com Yahoo:oneralarm_02@yahoo.com
Tel: 8613660203413 Mail:oneralarm02@gmail.com or ellen@oneralarm.com Skype: oneralarm02
TEL: 86-20-28251951/61037179 FAX: 86-20-28251952 :
|
|
|
Jimmy D
03/18/2010
11:23:34 AM
|
Gps page
Reply to onerellen's post dated 3/15/2010 11:45:02 PM
This is a GPS forum you twat!
|
|
|
Fred
03/19/2010
02:13:57 AM
|
205W broken screen
Reply to nick's post dated 3/13/2010 5:50:58 PM
Hey Nick, Or you can sell me your boken 205W so I can make one good one out of two broken ones! Such a waste - is it not.
|
|
|
vern
03/21/2010
11:38:20 AM
|
garmin gpsmaps162
need repair and having no luck. help!
|
|
|
Bill
04/19/2010
05:27:37 PM
|
Great GPS Repair Site
http://www.sharcnet-usa.com
|
|
|